Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
Two nRF51822s were mounted in one board One nRF51822 will be used as a TWI master and the other as a TWI...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
I am using nrf51822 with softdevice 7.3 and sdk6. I am having some strange problems in single bank bootloader. The nrftoolbox version 2.4.0 gets stuck at 94% during the firmware...
Hi,
(SDK v14.2, nRF52832)
I'm developing a Timeout Timer functionality, and was wandering if the following scenario is a good practice:
I don't want to have a interrupt...
Good morning everyone,
I am having a lot of problems configuring the Peer Manager.
I read several discussions on the topic, but either they are old (referring to ble_evt_dispatch...
Hello everyone,
I`ve 4 thingys and ran the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo . That works well.
Now I`m trying to add the nRF52 DK as a Node...
I am trying to perform a dfu upgrade according to: infocenter.nordicsemi.com/index.jsp
The exact command I am running is: nrfutil dfu ble -ic NRF52 -pkg dev_board_bl.zip...
There is something I want you to tell. Do you know how to allow other interrupts (specifically IRQ pin) while interrupting app_timer? I studied variously, but I can not find...
While I'm waiting on answers to other questions, I thought I would try to nrf_Logging with the Segger RTT up and running. It sounds like a pretty tool.
I have created a...
As picture, This is the external circuit of 52832, and I've drawn out P0.09,P0.10,P0.17,P0.18,P0.19,P0.22 of these six gpios, each of them for control purposes, and now P2...
Looking to make the nrf52 DK into a CR2032 coin cell battery tester. I tried a couple of sdk 15.0 examples, uart, proximity and another from a devzone case but not really...
