Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
Hi,
What is the proper way to set "real time" in nRF9160 with nRF Connect SDK?
I want the function time() from the file time.h to return the correct time.
I know that...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
Dear Nordic
I am using SDK14.2, I cannot pint info . SDK periphral uart and serial can't print also
nus example jlinkrtt print as below:
<00> warning> nrf_sdh_ble: RAM...
Hi,
I am using pc-ble-driver version 4.1.1 with the SD version 6.1.1.
I want to configure the TX power for the NRF52 USB dongle.
Do you have a code example for configuring...
Now I can build & download nRF52840 SDK example with Eclipse.
But Eclipse indexer(F3 key) can not recognize include folder.
So I added every include folder to .cproject...
I'm having a advertising device and then I want to stop advertising and prevent BLE connection from device that would have received the advertisement. It seems to work by...
Dear Team,
I am trying to add my Thingy 91 to nRF cloud, but I receive the following error :"There was an error adding your device: No device found with id 'nrf-xxxxx'....
Hi Nordics
https://devzone.nordicsemi.com/f/nordic-q-a/22595/can-not-received-ble_gap_evt_timeout-event-when-connect-timeout/88877#88877
Referring to the above post, I...
Dear,
I am trying to test BLE on the THINGY:91.
Follow the Q&A for "Introduction to Nordic THINGY:91" webinar, Q12 of @ Petter Myhre
I tried with Zephyr HCI UART example...
Hi,
I'm trying to debug my bootloader (I2C specifically) using Ozone. However the CPU only seems to halt when trying to debug the bootloader.
Also setting breakpoints...
