I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello, I'm developing application starting from blinky example extracted from nRF5_SDK_15.3.0_59ac345 SDK. I see (using nRF Connect) that the connection result as "unencrypted...
This thread in zephyr community has left me confused about the features supported. lists.zephyrproject.org/.../31926113 .
Can you please confirm I can advertise and make...
when i try to debug with the segger develoment envrionment using a segger j link
i get the following log and a generic error
this is straightout of the box code no...
Hi ,
I am working on a NFC project which has below requirements , could you please help check if we have any existed example I can test ?
1. Support standarded ISO/IEC...
I'm looking for a nodified 'Wireless UART example" that I can use for a range test.
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/wireless_uart_15_4...
Hello,
I have problems using nrFgo Studio with my J-link programmer. The "nrf5x Programming" section is greyed out when the j-link is connected to the PC and the MCU....
I am working on a client to collect data from a continuous glucose monitor. I see that the CGM Service has been part of the SDK for some time. But there is no matching client...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
Hi All,
I'm very new to this Bluetooth mesh technology. Currently I'm referring to client/server switch example.
Without making any changes in the firmware I compiled...
I am seing odd time strings from AT+CCLK... Like: "+CCLK: "15/02/01,00:00:08"\r\nOK\r\n"
I think it is required that AT+CCLK responds error until it has gotten network time...
Hi!
I work at Lund university and I'm preparing a upcoming course project course. The course is about prototyping and PCB design. I want to use the nrf9160 as a example...
I get FDS_SUCCESS after I do fds_write(&desc, &m_dummy_record).
But when I do rc_read = fds_record_find(FILE_ID, REC_KEY, &desc, &tok); I get an error code rc_read = FDS_ERR_NOT_FOUND;...
Hi all,
I am trying to develop an Android app to connect to a nrf52832 running the ble_app_uart example. Previously I was using the Android-nRF-UART codes as a starting...
