I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello
I am using gazell on the nRF24LE1.
I would like to know some recommendations on how to estimate a consumption on the side of the device based on the times and repetitions...
Hi. I just recently started using nRF24L01+. I am trying to simulate MultiCeiver using 2 mcus and 2 nrfs.
PTX sends a message on all 6 pipes of the PRX. The problems start...
HI,
I look at nRF5 SDK doc about Gazell,see that 'the nrf_gzll_device_tx_info_t contains the num_channel_switches parameter which can be used by application to determine...
Hello
I am quite a beginner and have been trying to get it work for 2 weeks now.
I would like to merge these 2 example codes from nordic:
Shockburst TX example...
Hi everyone,
I want to use MasterEmulator.dll (2.1.13.14) in my own application (C#) for development. Then I realised that line
MasterEmulator mMasterEmulator = new...
I am using nRF52 and Raspberry Pi 3 (with BLE).
In the Raspberry Pi, I am using bluez.
I was attempting to connect with the NORDIC_BLINKY app but the message below was...
Hi, I wonder how to get the Nordic SDK-examples work with VisualGDB.
As I would like to read TWI sensor values a good point to start from are the Nordic examples.
But...
my project is used nrf51822 mcu, it contains SIM, when the mcu is reading SIM data, and at the same, I take out theSIM, and the 51822's pin which is link with SIM is can't...
Hi, Nordic
I use SDK12.1 with nRF52832, I found one issue:
if I do not program bootloader, nRFgo Studio can program app.
First, erase all flash, then program softdevice...
Hi Everone/Nodiac
I had tried so many threads and previous questions but not bale to get my answer so asking after two weeks.
I am willing to send a string from stm32f4...
Hello,
I currently working with the nRF52832 chip on a custom board. The external clock is a 32MHz clock with +/- 10 ppm. When I use nrf_delay_us or nrf_delay_ms the delay...
Hi all,
I am using a C# application with the masteremulator dll to connect to a nRF51822 with S110 V8.0.0
I can bond with a new device, and communicate with it in a...
In developing the device, for very low battery consumption, I encountered a feature of the implementation Gazell (ESB) protocol.
When I send a packet from the DEVICE (PTX...
