I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hi,
I am using the nrf52832 dk for my project.
I am using the RX characteristic of the NUS example to send data from the phone to the dk.
In the same code i am also...
I tried to build the "nRF5_SDK_15.1.0_a8c0c4d\examples\crypto\nrf_crypto\aes\aes_all_cli\pca10056\blank" source code but I got the following error,
.\_build\nrf52840_xxaa...
Hello,
While i am trying to find the definition of SER_REQ_ENC_BEGIN(SD_BLE_GAP_ADV_START); it is there in the file ble_gap_app.c
When i right click on that function...
What is the difference between nrf5232, 1.8V and 3.3V power supplies? What should watch out for when replacing a 3.3V power supply with a 1.8V power supply?
Hi,
I'm developing a central application and I want my central to read the device name characteristic from 3rd-party peripherals. I do not know the length of the data in...
Hi,
I've been trying to develop a custom service for a Bluetooth application. This custom service (called ble_dts - Data Transfer Service) has two characteristics - Spectrum...
Daer sir or madam
I am the personal software engineer and want to check and receive the best answer about my question. If I use BLE to connect the both smartphone and device...
My hardware only has one spi slave and one spi master. So can I just set the spi slave miso pin as output in spis_init function? If can not, can I set the pull down resistor...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hi all,
Because of my customer special requirement ,I need two or three USB in my project .
But 52840 has one USB.Can I extend 52840 USB interface with a USB HUB?
With SDK V14.2, I was able to specify internal flash address argument into nrf_bootloader_app_start(uint32_t start_addr) and was able to boot into the address. With SDK V15...
Hello, I have a problem when trying to compile the light server exemple for the mesh.
I use Segger Embbeded Studio 4.16 (even though i tried the 4.15), mesh sdk 3.0 and...
