Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I am new to Keil and nrf51 development so please forgive me if I ask a stupid question.
I have followed the steps from the user guide and installed Keil (version...
I have scoured the internet for solutions, and documentation. Everything that I've found has to do with ADC, so I thought that I would just convert it to the LPCOMP(they're...
Hi all,
If I want to send a table that contains a structure in each of his cases using sd_ble_gatts_hvx(), can I get it ?
Knowing that the second parametre of sd_ble_gatts_hvx...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
S110 8.0.0 was just released allowing a larger ATT table, which is something we need, but is there a corresponding SDK update for this SD before we spend the time upgrading...
I am a very beginner on embedded field.
I have a nrf51822 and tmp 102. I follow this direction on mbed site
link text
and it's actually working. The code provide...
Hi,
I have a similar problem as described in
devzone.nordicsemi.com/.../
I have eliminated my program to be:
int main(void) {
setupLEDPins();
BluetoothPeripheral...
We are having some trouble with battery percentage measurement. The battery percentage being reported, keeps fluctuating. Earlier the fluctuations were as large as 3% to 100...
Hi,
I recently made some changes to the code and noticed the following errors for the first time.
Error: L6406E: No space in execution regions with .ANY selector matching...
Hi, all!
I am rencently studying ota,and that is what I have done:
Program softdevice 6.0 into my nrf51822 chip.
Program bootloader(version in SDK5.2) into my nrf51822...
hello everyone,
I recently purchased the new nRF51 dongle. I could successfully load the blinky example with S110 soft device to it. But it is not working with the HRS example...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
Hi all,
I have a small question. If a GATT server needs to send data to a GATT client(about 65 bytes), does it have to create a service first and then adds characteristic...
i am trying to make connections between s130 device and end node which have heart rate service.
according to the s130 document once if you press the button 0 it will automatically...
