Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
spim2、ncs2.6.1
I used SPIM2 to send the string "Hello, SPIM!" and receive data of the same length.
However, on the logic analyzer, I can only see the transmitted signals...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
There is a race condition in the SAADC driver when using buffer convert.
I am trying to drive ADC at maximum rate to sample 3 ADC channels, and so I call the following in...
Hello,
after I could not use the nRF9160 DK I bought almost a year ago in Germany due to the missing nb-iot coverage I was very curious about the Thingy91 and I assumed...
Sorry for a noob questions but it is essential at this moment as I have not done any development on NordicSemi chips.
What software and hardware tools I need to develop...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
Hi
Using the nrf52840-dk with SD S140 and nrfx_gpiote, everything runs fund (BLE, TWI etc) but interrup on pin 0,28 causes a Hard Fault. I can not get any sensible logs...
I am trying to modify the existing Thingy-52 code to have a 'new' characteristic. I used the existing Thingy code to 'clone' a new characteristic (a 2nd microphone channel...
Hi
We tested the idle feature(by AT#XSLEEP=0) on nRF9160DK, but no significant change of power consumption before and after enter into IDLE mode, is this result correct...
Hello, I would like to save a log in the nrf5340 FLASH, how many times is possible to write? May I write in the Application CPU Flash from the Network CPU FLASH when the Application...
Hello
I am trying to discover the correct scan interval/window settings to capture the advertized packets from a beacon transmitting every 100ms(10Hz).
Should I just set...
Hello! I've have been designing a custom board. The circuit reads ADC channel 1 for long periods, 1 hour at most. When the reading is high enough it will send an alert using...
Hello,
I am trying to build a remote control using NRF52832 SoC, SDK16.0.0 with softdevice S132 version 7, Keil 5.
I have to control a servo motor and i want to achieve...
Hello,
I need to send logged sensor data in external 4MB flash to a phone via BLE.
I am using a nRF52840 based module on a custom PCB. I am using SDK v14.2.
I am using...
