Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hello,
i am currently trying to add my own model to the Mesh Android App. It should just be a simple sensor model.
It already works to have an own Window, where I can...
I want to store data on a specific location in Flash, so it is available later on in a bootloader. The size of this data can be quite large (~ 300 kB). I'm kind of puzzled...
Hi,
I've developping a firmware for the nRF52832 with the nRF52DK and it work on this board and on an external BLE module from EBYTE (E73).
I want to flash an other hardware...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
I'm currently developing a custom bootloader for DFU, using I2C.
The bootloader is based upon the secure UART bootloader for nRF52832. Transferring and writing the...
Hi Nordic Team,
In the recent Nordic APAC Event, we got nRF52840 Dongle and we would like to use it as BLE sniffer.
Can you please point out some resource/link which...
On the NRF52840 what is the max speed I can program the unit at. In the datasheet SWDCLK says it has a max of 8MHz. Is that supposed to be the max. I have two segger programmers...
I am using the nRF52DK board.
I use the " ble_app_template_pca10040_s132 " for testing.
I want to advertise 2 custom UUID (SERVICE_DATA " 0x16 " & SERVICE_DATA_128BIT...
Hi,
We are in process of picking the right part from Nordic portfolio and are looking at nRF52 Series parts.
We are looking for best performance in below two aspects...
Hello,
SDK: 15.3.0
nRF52840-DK
s140
I have taken the flash_fds_s140_pca10056 example and modified it for our own use. I would like to store versioning information...
Hi Team,
I am working on nrf52840, for openthread application
I flashed cli code built with USB=1 (enables Nrf USB J3), DIAGNOSTIC=1 (enabling factory diagnostics) option...
Hi !
I use SDK:15.3.0 ,Mesh v3.2.0 and have tried official dfu example which is ok.However, When after I enable marco "MESH_FEATURE_PB_GATT_ENABLED=1 MESH_FEATURE_GATT_PROXY_ENABLED...
