Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
nRF5 SDK v15.2.0, nRF52840
This issue occurs on reset, most often after cycling power.
There are 4 pages reserved and 4 data pages are found. Since a swap page isn't found...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
I am working on NVMC. I was going through the product specifications for the NVMC. In that, it's given that the number of write operation limit is 181 for a block in nvm....
I'm trying to get the PPK working when connected to aNRF52840-DK, but getting the error - Error while setting up device [REDACTED_SERIAL]: Error occured when close opened...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0 in my customboard.
As peripheral, device communicate Ios phone by using ble.
However, my device sometimes...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
I am working on ble_app_blinky trying to add the capability to transmit data to another device(e.g Arduino).I have already enabled APP_FIFO_ENABLED ,APP_UART_ENABLED and UART0_ENABLED...
How to add uart peripherals to mesh. Thank you very much
How to add uart peripherals to mesh.Thank you very much
How to add uart peripherals to mesh.Thank you very much...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT.
Only PB-GATT is turned on, is the device only sending GATT broadcast packets.
However, I now need to...
hi
In mesh 3.0 sdk, why does the lpn example only enable PB-GATT. Now,
I need to make a product. Support PB-ADV. And it is an LPN device. What should I do?
I am using...
Hello,
We are currently evaluating the Bluetooth Mesh solution for our product-line that consists of a Bluetooth Gateway that can communicate with battery-powered devices...
Hi All,
I am using light_control example from Mesh SDK and I need to get something that identify my device in mesh e.g id, address. I would like to send some message to the...
Hi,
This is somewhat tricky question.
In my custom board application program using nRF52832 chip,
I used uart initialization function (e.g. uart_init()) and printf...
