در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
My board env as below:
nRF52832, pca10040, SDK14.2.0, S132
I am trying advertising sample according to the tutorial
devzone.nordicsemi.com/.../
The "Address...
Hi,
I'm trying to build and install my first code that uses the BLE / softdevice to my NRF52-DK
I'm using Windows 10, Eclipse/gcc and nRF5_SDK_14.2.0_17b948a I'm able...
On my peripheral I filter the devices connected and refuses them when not bonded.
When a device not bonded tries to connect to the peripheral, it forces the disconnection...
Hi,
I am using nrfsdk11 nrf52 and s132 soft device. In my code,I am doing this in main();
void fs_evt_handler(fs_evt_t const * const evt, fs_ret_t result)
{
if (result...
hello sir,
i am using ble mpu example and it working fine now i want do send some commands from mobile to nrf52832 chip via these commands my application should work.
...
Hi everybody,
I will to use the nRF52832 QFAA for a drone, and I carried out this schematic for this chip.
I have two questions :
For the capacitor C6, which value should...
I'm trying to start my app from the bootloader, which is funcionally basically the same as the one in nRF5_SDK_11.0.0_89a8197.
To start the app I call bootloader_app_start...
Hello.
I use nRF52832 and its dev board, S132 soft device. nRF5 SDK v14.2.0 is the version number.
I want to change some manufacture specific data from mobile app. Like...
I am working on the nrf52840 kit with the ble_app_beacon example, compile and download the code successfully. But I don't know how to test whether the kit is advertising,...
I have my own hardware design with the nRF52840 on it. I more or less copied the whole radio/antenna part from the dev kit reference design. The blinky example works fine...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
