nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
Hi,
in want to extend the DFU library (Android and iOS) with a function similar to setBinOrHex(). But instead of a filename, i want to give a byte array with the init packet...
I think there is a bug in Nordic provided code in this thread about fetching the offending PC in a hardfault handler:
devzone.nordicsemi.com/.../
The provided code is...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
Hi!
I am fairly new to programming micro controllers so apologies if I ask many questions.
I am using NRF52832. The situation is this - I have 2 devices and 1 host . After...
Hi all,
I've found the nRF52840 with USB but it seems a bit OTT for our application, something more like the 51822 would be nice, but cannot identify one, can anyone list...
Hello!
I have a code that is working perfectly on Eclipse for Linux and I would like to copy it to a windows computer with keil. I created a new project with Keil copying...
Hi, I'm developping endless PWM sequence.
That is ...
Only one output pin and the signal from it is repeated with the same period of pulse but with two different duty...
Greetings,
I'm having some trouble using the secure DFU bootloader and buttonless DFU service in my application. The code for both of these has been taken from their respective...
