Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
Hi I'm an undergrade student in dongguk Univ. in South Korea.
I want to control the sending message and receiving message.
I use the android studio.
What do I do...
Has anyone using nRF24L01 raw (CRC turned off) mode. I try to turn off the CRC (the data sheet offers this option), then I start to miss packets. Once I turn on the CRC, I...
In ble_app_uart, the tx and rx characteristic uuid are shown below, and it supposed that the Tx characteristic enable notifications while the Rx characteristic enable write...
The hardware I am using is based on nrf51822/pca10028, with s110 SoftDevice version, and the SDK version for the project is 8.1.1 Using Keil uVision 5.21.A
When opening...
Hi,
I am running the mqtt subscriber example provided in IoT SDK (nrf5_iot_sdk_3288530).
I am using raspberry pi as router, and following the infocenter tutorial .
I have...
Hi ,
This is the first time I am using nRF52 and I don't have any experience about Antenna design. Here is my question: I am using nRF52 CIAA variant and planing to use PCB...
Hi,
I need to change advertisement data while advertising. The goal is to set new data for every packet. Firstly, I was trying to put new value like this, but it didn't...
hi all:
Recently, I develop with nrf52832, the softdevice is nRF52_SDK_0.9.0_0c82e3e.
In my application, I need a big buffer, so 32K ram can not satisfied. As the errata...
Hi all, we designed a custom board using nRF51822 now we need to test these custom boards working properly are not for these I'm creating a factory test project by configuring...
Hello Nordic Semi Developers..
I design my Product prototype using NRF52832
What is the plan of Nordic to provide SDK to support NRF52832 dynamic Mesh with
[1] Over The...
Hello,
I want to read the current ticks in RTC0, and want to measure the time elapsed after some events by using ticks to milliseconds.
Basically i want to display the...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
What I want to achive:
Get the IoT-SDK 0.8.0 MQTT-Example running on nRF51 and publishing sensor data...
I am using nRF51 IoT SDK and nRF51-DK.
After setting up Raspberry Pi3, I ran icmp sample in the SDK for testing ping6.
when sending about 60k byte, we could not send the...
Hello, I used to think that handles are just a member of a stuct or perhaps a field of a packet, which is used to identify data payloads.
Now it seems that I might have...
Hi,
I have a problem with the nrF8001. I connected to STM32F4 and I use the nRF8001 SDK v1.7.
I need send several (less then 20) bytes from the device to the phone with...