Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
I cannot find my nRF52 (PCA100040 / SD132) when scanning for devices from my nRF Master Control Panel on my Android Phone.
In these two posts ( post1 and post2 ...
i have nrf51422 v2 that its compatible with sdk v6 and s110 v7
when i run the example of this sdk , only one phone can detect it and that is nokia windows phone
HTC and...
I have known that is AES-128 for the security solution on nRF51822.
We need more powerful security function and algorithm.
As this developer zone, Bluetooth Core 4.2 has...
We are using NRF52832, SDK 11.0.0.2 alpha, S132 soft Device ,I need some clarifications on using SPI,
In nrf52832 SPI Master driver is it possible to create two SPI...
I am evaluating the Keil compiler, version 5.18 with a Nordic development board (PCA100400) running the nRF52832
I just downloaded and installed Nordic's nRF5x-MDK-Keil4...
Here is the link to the image how we set it up: Click Here to See
We are getting a fatal error while running "Master Loop Back" example. We have also tried "SPI Master...
I use the nRF51 chip with a UART communication. I developed a protocol on the UART to communicate with another processor or a PC. Every messages of the protocol have 2 bytes...
I have an arduino connected to a redbear BLE shield.
the BLE shield uses nordic nRF8001 chip.
How could I implement RSC ? (running speed and cadence)
I would like to...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi!
As a student, I am starting a new project on university. Project is based on beacons idea, so I decided to use Nordic's chip as an MCU.
I am trying to decide, which...
Hey folks,
I am going to join Nordic Developers community, but before I can do that I need your help.
I am quite familiar with software development, however, embedded...
Hello,
DFU issue (FOTA application update fail)
I have a problem when performing Application update over the air , after i change my boot loader.
so when try FOTA...
Hi,
I am using two Android devices with nRF Master Control Panel (BLE v4.0.5) app installed on both. I am using one Android device (Moto G 3rd Gen Android v6.0) as the...
Hi all,
I see that the nRF51 doesn't have a PWM module and a software PWM library is needed. How well does the software module actually run? I've had rather bad experiences...
