Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hi,
I am developing a custom profile for an application.
This custom application works fine with Master Control Panel and nRF toolbox on Android.
I am also developing...
Hi,
I am using the sample ble_gls code from Nordic.
Currently it advertises for 180 sec and than resets or goes into sleep mode.
If i want to advertise continuously what...
Hello,
I am just starting working with the nRF52 development kit and have a couple guidance questions. I'm very new to the Keil environment and am having a little trouble...
I'm using s130_nrf51_2.0.0-4.alpha as central and do some testing with channel map.
I set the channel map before I'm trying to connect to a peripheral with:
ble_opt_t...
Hi experts,
I want to send 20 packages from nrf51822 to phone, so I tried to call sd_ble_gatts_hvx() repeatedly until BLE_ERROR_NO_TX_BUFFERS returns, then sent left packages...
I have a question about the NRF518222, we using 3v coin cell battery as power for Ldo working mode.
The connection between the devices and mobile phones, regular, disconnection...
nrfjprog is reporting known errors while I'm trying to burn the pca10028 dual_bank_ble_s110 bootloader to the nRF51-DK.
".\_build\nrf51422_xxac.axf" - 0 Error(s), 0 Warning...
Hello there,
First of all, thank you Nordic for such a great platform to develop on and all the great example code to get a BLE newbie up and running. Also, a deep thanks...
I am trying to control a servo motor from nRF51822 when BLE is activated. I am using mbed development framework and libraries.
My servo example works flowlessly if BLE/SoftDevice...
Hello,
Recently, I used the LedButtonDemo to create a program which make one rotation on a step-by-step motor.
The program is very simple : in place of toggling the led...
I am using the nRF51422 for sensor. This sensor is paired to a slave in the most simple way: the slave searches with a wildcard for a sensor and the stores the devicenumber...
Looking for a 3rd party supplier with a certified module.
Module pinning makes it possible to program new software into the module.
The question is: If I change the software...
Hello,
I am using nrf51822 with softdevice 110.
I have noticed that there is some power usage between advertisements, that is more than what is being used when no advertising...
We're having difficulty preventing our nRF51822 from resetting when ESD events occur. These events are not directly on the nRF51's I/O pins, and we've tried things like grounding...
