Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi all,
In my application, I take mac address of chip and make major, minor value (device 's ID) and I need mac address is a constant value. As I know, mac address is a...
because license is so expensive, I'm converting my project to OSX GNU
I'm solving problems step by step..
and there is error that I couldn't understand.
Anyone can...
Is there any way to control BLE shield 2.1 from PC rather than android / iOS app.
Also if i pass any message to BT dongle how to check the received messages.
And in...
infocenter.nordicsemi.com/index.jsp
I see a debouncing filter in the block diagram of NRF52 preview DK. Isnt debouncing implemented in software? So why need a HW debouncing...
Hi all,
I have two kinds of NRF24LE1 devices(A and B), and I want to realize that one device_A can communicate with 10 device_Bs at the same time. To explain it in detail...
I would like to use 3 PWM for controling RGBs. I use a softdevice because I want to control the pwm trough the MCP. But for now I just want to get it work to initialize these...
whether linux and bluez implemnted the simultaneous master and slave connections......?
or is it part of link layer only..?
does this feature need kernel support or not...
In the NRF51822 reference manual, the debug interface mode initiation routine is described as follow:
150 clock cycles with SWDIO=1.
I have already verified that a standard...
Hi,
I am wondering about the Cumulative crank revs for service 0x1816 & 0x1818
Cycling Cadence and Speed, Cycling Power Services
I dont understand why the crank revs...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Ok, so I've been trying to get to the bottom of a problem for a few days now where suddenly the app_timer is acting like it's on crack and running super fast, i.e. triggering...
hey,
i want to discover the PCA10001 board with PCA10000 board in master emulator. i have programmed the blanked PCA10001 chip with softdevice(s110_nrf51822_6.0.0_softdevice...
I want to generate PWM.
I set timer2 events_compare[0] to toggle pin 1:
sd_ppi_channel_assign(PWM_LED_HI_CHANNEL, &(NRF_TIMER2->EVENTS_COMPARE[0]) ,&(NRF_GPIOTE->TASKS_OU...
