Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi
Maybe silly question:
I was wondering: if I cast a pointer to a uint32_t to an array "buff" of uint8_t, what is held in buff[0], MSByte or LSByte?
Or in other words...
Having just upgraded to the Soft Device 6.0.0 and SDK 5.1.0, I can no longer flash my nRF51822 from Keil. I get this in the Keil console:
Load "C:\\Users\\Eliot\\dev\\nrf51_sdk...
Hi,
I'm designing a four layer flex PCB with the nRF51822-CFAC and recommended ST BAL-NRF02D3 balun and PCB trace antenna (not chip). I have a couple of questions.
...
Greetings,
Using the "central multilink" example project, how do I stop scanning if no advertisers are found? I see a case BLE_GAP_EVT_TIMEOUT in function on_ble_evt() but...
Hello
I found similar questions but no answer?
In the manual is written that I can control the parity bit in manual mode with the TXPARITY register but I can not find how...
what may be the reason for app_assert _callback error in s130,ble_central_and_peripheral that occurs from the following 2 lines
sd_softdevice_enable((uint32_t)NRF_CLOCK_LFCLKSRC_XTAL_75_PPM...
I have Rezence SDK working well with Keil uversion with wired and wireless debug without any issues on either nRF51 and nrf51822 DKs. When I port the project to Eclipse with...
Using the bootloader example code in SDK 8.1.0 for gcc, roughly how long does it take from power on to the call to bootloader_app_start()?
My device is motion activated...
Hi,
I have nrf51dk and analog EKG sensor. I know that ble_app_hrs allows to get R-R interval, but in my application i need to get also R-S and R-T intervals (or just R...
Hello,
I have combined two files spi_master and ble_app_uart into one file. Once trying to compile main.c compiles with no error but bsp.c compiles with 3 errors although...
Hi,
in S110 v 8.0.0, we can select the advertisement channels by setting the advertising parameters for sd_ble_gap_adv_start(..).
But what I want to do is to change...
Dear Nordic Team,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice with the following requirements.
Read ASCII chars from a third...
i have found that
devzone.nordicsemi.com/.../
It seems impossible to connect two nrf51822,because soft device doesn't support the BLE Central role.But below said in...
