Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
hello everyone,
i am trying to use SDA and SCL pins of TWI other than 24 and 25, is it possible? i want to know before using other pins for twi other than 24 nd 25 with...
Hi
I try to communicate with others TWi devices using the twi_hw_master driver.
When i initiate a communication with twi_master_transfer , i don't receive any ack from...
Hi,
I have purchased the nRF8001 Development Kit and so far I wired the nRF2740 board to a FTDI VNC2 microcontroller. I have been reading about how to configure the 8001...
Hello. I'm trying to port the ble_hrs to a custom board with an NRF51822 on it, but the advertising never starts. While I'm debugging this, what should I be looking out for...
Is there an example for sleeping? I just want to put this thing to sleep drawing minimum current and have it wake up on a RTC timeout, but do not seem to be able to achieve...
As indicated in the PS, System On Mode idle draws only 2.6 uA.
Does this mean that if I install and active a timer interrupt, where the interrupt routine places the system...
Hi,
I am new to ARM development. We are thinking of ordering mkit for evaluating and developing a custom BLE service(profile) which sends data to BLE client (probably a...
Hello Everybody!
I have been working with BLE security and I have an issue with OOB setup.
I'm setting my nRF with the following:
m_sec_params.timeout = 30;
m_sec_params...
I was reading this press release:
http://www.nordicsemi.com/News/News-releases/Product-Related-News/Single-board-Bluetooth-Smart-Arduino-solution-is-low-cost-and-can-be...
Yo!
I'm very concerned by what I hear about Bluetooth Low Energy security. According to this guy , who presented a paper on the subject at a USENIX conference last year...
Any experiences about analog sensor LM35DZ? I used this example: main.c
The LM35 data sheet says it will operate from +4V to 30 V supply. I'm use supply only Vcc pretty...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I'm using API 2.1.3 and I'm having problems with SendData blocking forever at the end of a process. I placed access mutexes around each method call to the library, as well...
