Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Now we have a new project,in order to long distance communication,we add a PA RFX2411N in our design,now how may I tuning the pi (or T) match network between nRF52 chip and...
Hi All, What is the best way to modify ble_app_multilink_central and ble_app_blinky example codes, so BLE tag can send to ble_app_multilink_central Its own address. The ble_multilink...
My application uses a NRF52 (SD132, SDK 15.0.0), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
Hi, I'm having some issues with migrating from SDK12.1 to SDK16 while discovering services.
It seems to connect to Android without much issue, but on iOS the connection...
A project is currently utilizing an NXP module to access the SD card via 4-bit SDIO. I am exploring the feasibility of integrating an nRF52840-based module, and have a few...
I am trying to use the battery example in " /ncs/zephyr/samples/boards/nrf/battery" to measure my 3V coin cell via VDD. I am using P0.14 to enable a set load on VDD before...
I'm using a nRF52840 DK (PCA10056 2.0.1 2020,14 683193023) with an adafruit FTDI serial TTL-232 USB cable (part number P70C uses the FTDI -FT232R chip inside a translucent...
i use pca20023-sr3_nrf52832_product_example demo to test, but there was an error occued , the segger rtt views displays:
00> [00000000] <info> app: System ON 00> [00000000...
Hello,
I'm in the process of developing the HW board for a nRF5340-based product. I need the customer could update the firmware using a serial port (USB or Bluetooth is...
I am testing a number of boards with a QSPI memory module with NRF52840 chip.
The QSPI driver functions all return without error even if the chip is not present. What is...
I have made PCB 32mhz crystal footprint with error. I have used other khz frequency too. Now I can't solder 32mhz crystal is it possible to code nrf52832 and control various...
Hello,
I wanted to test the long range, so changed the primary and secondary PHY to BLE_GAP_PHY_CODED from BLE_GAP_PHY_1MBPS in the advertising_init() of the peripheral...
I'm trying to debug a Zephyr application on nrf52DK. However, due to the use of multi-threading (in Zephyr) I can't use J-Link Debug Server (as I'm used to). For executing...
Hi,
Can you please answer below queries.
1. Do you support CIoT EPS attach without PDN connectivity optimization? 2. Do you support UE Usage Type (HSS and Samsung MME...
