Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I try to run the example project "ble_app_hids_keyboard" on a NRF52811 (I use the PCA10040e project, adapted to the NRF52811 on a custom board)
and I always run in...
Hi,
I was reading the values from the FICR of my nrf9160 on my thingy91 and I noticed that when I read the INFO.PART register from the FICR, it returned 0x00009120 rather...
we have BorderRouter- Raspberry pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI...
I am developing application with buttonles BLE DFU and FreeRTOS. I needed debounce on buttons and decided to use app_button. Here is my init:
I turn on log debug on app_timer...
Apologies for this question, as it has been asked a number of times but I've not found anything to help so far.
As at the time of writing, I believe I've got the latest...
I'm trying to deploy a new firmware to my hardware device but I get the following error in the nrf Connect 3.6.1 programmer (v1.4.8):
16:47:36.937
Error when getting...
Hi,
I noticed that the PPK2 turns off the internal voltage regulator upon disconnecting from it. Is there a possibility to change that behavior? I would like the voltage...
Hey Guys,
I have the nrf52840 as the peripheral and my application use varies depending on which central I am connecting to in terms of:
PC ( Windows or macOS or Linux...
Hello,
I have been recently trying to initialize fds in my application, through the assistance of the given flash_fds examples in the SDK (15.3).
Currently, I'm coming...
Hi, I'm working with flash, I've started with the example code from flash_storage, as I will need to use flash while using a SoftDevice.
I use NRF52 Dongle and SDK17.0.2...
hello,
i am using nrf52840 dvk with sx1276 lora modules and trying to read my device address using spi i am just calling the below function in main
uint8_t spiCommandData...
Hello everyone,
I'm currently working on porting a device driver to Zephyr on the nRF9160. I have defined a device tree and set up the device through the .overlay file...
Hi
I was wondering if there is any further reading about the Automatic network selection set as <mode> in the +COPS set command.
Especially, I'm looking for a solution...
Hi,
I just recently began implementing the mesh stack into an existing application, using mesh v3.2 and nrf sdk 15.2.
Integration works well by using the integration guide...
