I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi, I have been working with my nrf51 DK for a while now without problems. When I first connected the board to the computer today, the ld5 led was blinking very quickly, and...
hi
i have a question. I'm working on a type of beacon system and need to advertising repeatedly unique beacon in less than 100 ms advertise interval that limited on non...
Good day!
In Light Switch example I made some changes to have GPIOTE events, instead of Simple HAL.
Now, when I try to publish message, debugger shows error in bearer_event_in_correct_irq_priority...
I want to send static data from nrf52 to esp8266. I have used serial Program from examples. I am able to send data dynamically from the serial monitor.
I'm attempting to write a library to allow a NRF52 DK (PCA10040) to read data from a ADXL375 accelerometer through SPI. I'm using SDK 15.0.0. I am able to read from the registers...
When I use the following link
nordicsemi.com/start9160dk
I get a webpage with the following message
I have tried the 2nd suggestion mentioned plus using google chrome...
I'm very new and trying to get the nRF Blinky example to work with an iPhone with an nRF52840.
I'm able to connect to the device and it seems to be reading and writing correctly...
I am using S130, SDK13 and NRF52832 both on my central and peripheral - custom boards.
I am trying to avoid service discovery on my peripheral.
I have set the service_changed...
Hi, Does anyone know how to modify the asset tracker so that rather than point to the AWS URL it points to a fixed IP address?
Also is the port number fixed?
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832)
When connecting...
Hi,
When I test nRF MESH application on android phone with other mesh device, after discover services, it always use proxy data in to write data to device for provisioning...
Hello there,
We are planning to use MQTT and nRF5 boards in the project. We've successfully tested out MQTT examples provided in the SDK using BLE router on Raspberry Pi...
Hi,
We are trying to establish communication between ESP8266 and NRF52832 over uart using Baudrate 115200, We are also controlling the ESP8266 boot and power through GPIO...
