I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
I purchased the nRF52840-PDK the other day and when it came in today Booted it up and it worked fine. I went to load the example nrf52840_xxaa_side_header.hex from the github...
It worked before when I connected my nRF51 board to my windows 7 computer. The green light is on.
But today when I connect them the light is blinking rapidly and there is...
Plugged in board to Win 10 pc that was working properly in past. Start NRF tools and get error.....
ERROR Unable to read connectivity firmware version: Unable to get version...
Hi,
I'm using SDK v14.2 and s112_5.1.0 for nRF52810 basing on the ble_app_uart example. Now we use the uart to communicate with external MCU. Also we want to close uart...
Hi
I don't get a connection when I run boards from PCBWay, but it works fine with the same boards manufactured by Eurocircuit. When I comment out the statement below, boards...
I am using an nRF52DK kit, SDK V11.0.0 and SoftDevice S132 V2.0.0. I have found an advertising example on the site github.com/.../nrf51-ble-tutorial-advertising . I have modified...
Hi,
We made a custom PCB using the NRF52832. We have connected a button to P0.21 which is the reset pin. We have configured this button as input and set the preprocessor...
Hi,
I am using multiperipheral configuration. I want a characteristic to be read by only a specific peer among connected peers. How do i recognize and authorize this specific...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all!
I´m trying to use FDS to read and write to my nRF51 using the example from Infocenter.
The write seems to be OK and returns 0x00.
But fds_record_find() returns...
Hi everyone.
I want to add RFX2411N to extend BLE signal coverage. I also need to minimize power consumption. I used VDD_PA to control TXEN and 2 gpios control both TXEN...
Hi,
I am testing the USB CDC ACM Secure DFU Bootloader example via NRF52840.
softdeivce uses 5.0.0-2 alpha and uses SDK version 14.1.
I have a problem.
I ran Erase...
Hi,
I need to activate one pin just before the sample is taken on a saadc channel. I have settings as in saadc example.
How can I do this? Is there any event that I...
Is it possible to send more than 255 bytes on SPI when nrf52832 is used as slave. A few solutions use SPI Master with easyDMA and ArrayList to do this. Will the same solution...
Hello,
I have a question is it possible to break the nrf52832 if I try to load the application when the UART of the module is active(TX and RX pins are 1).
The softdevice...
