Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi,
in NB-IOT the UE should make a Traffic Area Update TAU when timer T3412 expires. I have a project based on the UDP_with _PSM sample. When I configure the PSM timer to...
Dear All,
I am trying to minimize the current consumption of my device. I am using several peripherals, such as UART, I2C and ADC.
When I run a very simple sample...
I am working on a line of products that use the same Microcontroller and softdevice so the same QDID. Most of them work with a module and one has the same chip mounted directly...
Hi, I'm using this post to upgrade from SDK 11.0 to SDK 15.3.
All goes well, until I uploaded an application: then I get a hardfault somewhere at fds_init().
I found...
When I start nRF Connect v3.2.0 the first window starts as normal, but when I click on Open Bluetooth Low Energy the nRF Connect v3.2.0 - Bluetooth Low Energy window is blank...
How can application code interrogate the SD140 to identify which version (such as 6.0.0) is running.
We pre-flash (before SMT) our nRF52840 with a bootloader and SD140,...
Hi ,
What does the handle parameter in status_handle(access_model_handle_t handle, const access_message_rx_t * p_rx_msg, void * p_args)function (generic_onoff_client.c)...
Hi all,
I am trying to reduce the connection time between each connection to the minimal posible
Connect -->Transfer data -- Disconnect
I am facing two options...
Hi,
I want to make simple software that runs on PCA10056 using SEGGER and SDK. To learn how to use SEGGER, I copied exsamples / template_project and tried to imitate blinky...
Hello guys, i'm using nRF52832-DK with S132_v3.1.0 and SDK v12.2.0.
When other BLE device write some value to my characteristic, how do i know
that my characteristic...
Hello,
I am using a custom board that has a DSP and the Lairds BLE module BL651 that has nRF52810. I have written a simple program that sends a test data byte to the DSP...
I use nrf51422 dk, device: s310 2.0.1
Then i want to download "bootloader" from example floder by keil 4
but it can't work
and show up "JLinkARM.dll not found. please reinstall...
Hello,
I want to install nRF5x Command Line Tools on macOS, I found this user guide, infocenter.nordicsemi.com/.../nRF5x_Command_Line_Tools_v1.3.pdf and on page 5, it lists...
hello guys,
I using nrf52840 development kit and segger embedded studio. I want to write a program to implement spi protocol, can I get a simple reference code to write...
