Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am implementing ContikiOS on my custom nRF52823 board. I have been following the instruction here: github.com/.../README-BLE-6LoWPAN.md
I am running Debian 9 testing...
Hi,
I am trying to use the p21 reset pin as gpio but it is not working as expected. it is showing a 3.3v even when i am trying to toggle the pin. I have removed the CONFIGURE...
Hello,
I am just starting to develop on nRF52840. I want to use the USB functionality. Could you please let me know how to get the Vendor ID and Product ID?
Kind regards...
Hi,
I am trying to use the bit counter to get an indication about the length of the data I am sending.
After trying around for a while it turned out the value of the bit...
Hi
I'm using S132 V5.0.0 with the nRF52832.
I tried to add an include declaration to the last added primary service by using BLE_GATT_HANDLE_INVALID as service handle...
Hello Everyone
I want to interface an external flash mx25r6435F with nrf52832. i ll be writing and reading some data. It should be spi .
Can you guys please suggest me...
Hi, everyone, We develope the BLE project on nRF51822 tool that uses the ADC. But the read measures are different from IC to IC. At the link devzone.nordicsemi.com/.../how...
Hello,
I have see this demo
.hex are available witch is already nice, but I would like to get everything needed to reproduce it.
Does someone know if it's possible...
I'm using a custom device which has two services and each of them has one characteristic. I'm using notifications to send data to the other side and on each notification complete...
Hello!
I am a huge fan of "nRF connect"! This software is helpful! Thank you Nordic for giving us this for free!
When playing with a few devices (TrackR, Thingy, non-Nordic...
Hi Guys,
I need to implement the Zigbee gateway function on nRF52840, I have download the Zigbee SDK from the Nordic website, but currently only have version 1.0, and I...
Hi,
I am trying to send accelerometer values through bluetooth for nRF52832 and SDK 14.2. I am using "nrf-mpu-simple" program form this ' GitHub ' repository and added BLE...
Hi,
I use EasyDMA with UART.
I'm in permanent reception and the received octects go directly into a memory buffer.
When the buffer is full, the writing starts again...
I have been using a JTAG to program a nrf52832 chip (SD v15) during development and am now testing firmware updates from iOS. As part of it, I've made a firmware package using...
Hi,
the default board of the homekit SDK is PCA10040.
I want to run ble_hk_doorlock_static demo on board PCA10056 , What changes should I need to do?
tool-chain :...
