The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
I'm in the process of designing a consumer product using the nRF51822. I'm using the "square wave" antenna and matching circuit exactly as the are in the development kits...
Hello,
we are based in Germany and need a way to mass-programme the nrf51822 for production with our custom firmware+the softdevice.
Unfortunately we haven't found any...
Hi
I am writing an application that will have to switch the radio in between a number of different modes. (With/without AutoAck, and with/without dpl).
I have been looking...
Hello,
according to the documenation, the function sd_ant_burst_handler_request() can return with the error code NRF_ANT_ERROR_MESSAGE_SIZE_EXCEEDS_LIMIT. When will the...
Hi,
I was thinking if it is possible to use, per example HackRF greatscottgadgets.com/.../ , to tune the antena of the nRF15822 seeing if it is transmiting on the 2.4Ghz...
Hello,
We developed the energy harvest application equipment with the HRM1017 module.
The function is every simply as follows:
After initialization, CPU scans 4 I/O ports...
Hi,
I am searching for a way to disable then re-enable the BLE packet transmission on PTU.
This is for testing the A4WP conformance test PRU/PC/GR/Link.
"Disable the...
Hi,
I just got an Arduino and a BLE shield. I was following the Smart Starter Kit. The demo project have me errors, so I just started using the proximity example, and editing...
Hi,
I am using the nrf8001 module provided by adafruit ( www.adafruit.com/.../1697) but it's not clear if the RDY and REQ pins available on the chip are active low or not...
