Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
I'm trying to use the PPK with an nRF51 dev board, and I'm getting this output whenever I try to start the PPK Software:
Checking installed packages
pyside: 1.2.4
pyqtgraph...
I tested a 23byte data transition in iPhone 5s with Softdevice 3.1.0, sdk12.2 .
it is ok. I know that iphone 5s is ble 4.0.
So I thought it would be possible on Android...
How do I set TIMER2 to interrupt every 1 ms?
Sounds like a very basic question, but I haven't succeed. For TIMER1 I can get it working, but for TIMER2 the highest frequecy...
I am using SAADC and reading in 1 analog channel. The data sheet says that scan mode is enabled when 2 or more channels are turned on. What if I am only using 1 channel ?...
Hello, after I program bootloader, sd, application, I did the following command to do read back protection,
nrfjprog --rbp ALL -f NRF51
But, even though I still can...
Is there a way to achieve what bsp_event_to_button_action_assign(button_id, action, event) does but using my own button?
The functions requires a button_id like 0,1,2,3...
When I use NRF_LOG_GETCHAR() witn nRF52 DK and onboard SEGGER UART it stops in next NRF_LOG_INFO(). Also after ARM reset it keeps in this error state. It seems that SEGGER...
Hello,
I'm trying to install wireshark sniffer on ubuntu 14.04 with PCA10031.
I follow this guide : devzone.nordicsemi.com/.../
But when I launch sudo python example_linux...
Hi,
I am trying to replicate the "Throughput and long range demo" from devzone.nordicsemi.com/.../
I have two nRF52840 boards. I am using IAR studio. I can compile,...
Hi,
i am working on TWI sensor example in SDK1. in which i connected SCL And SDA pins tonRF52 dk boards sca and scl pins. and connected voltage and ground. when i run the...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hi guys,
I want to implement the periodical transmit over the mesh network. I have 3 nRF52832 DK, and I use the nRF OpenMesh example.
What would be the best way to implement...
It appears this example hangs after the following call. Does the experimental 12.2 buttonless DFU work ok?
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);
Using SDK 12.2 and BDS plugin version 1.2.2
Module nrf52832_xxaa
Copied plugin output to nRF5_SDK_12.2.0/examples/ble_peripheral/experimental_bluetoothds_template/...
I have observed that the "Experimental Buttonless DFU Service" and its characteristics has the same UUID. But in case of other services(like battery service) the UUID for...
