Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I just realized this feature is available from NCS V3.3.0.
Does it support nRF52 series such as nRF52832 with DFU through BLE?
In this page, it seems only nRF54 are included...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
Hi,
there are several devices with same Firmware/Modem firmware/Hardware. All device were working. While all others continue to work, one suddenly gives me this:
Once...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi Team,
We want to load azure certificate into nRF9160, can you please provide sample code, code snippet to load azure certificate.
Regards,
Sravan Rikka
Summary
On NCS v3.3.0 , building any application that enables the new Zephyr OpenThread Border Router L2 glue ( CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y , together with...
Hi! This is a general info post since i have found a temporary fix to it, but whilst trying out ntn, we noticed that when switching from %XSYSTEMMODE: 0,0,1,0,0 to %XSYSTEMMODE...
Hi, we use BMD-350 modules (nrf52832) in our product which has been in production for over a year. Our DFU service is very well tested.
a couple weeks ago, while performing...
I'm planning to deploy a Thread network with 200-400 units and seeking best practices and real-world experience from the community. While the Thread spec allows up to 32 routers...
Hello Support team,
I have an issue with two simultaneous heaps in my project. I use nrf Connect SDK 3.2.2 with the next configuration options:
CONFIG_REQUIRES_FULL_LIBCPP...
