Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello, i want to know is it possible scan iBeacons with a node using nrf mesh with proxy features like the light switch node server example? if this is, how i could start...
Hello.
I have pa/lna on my device. It works properly in application (rssi is about 30 dbm). But when application goes into bootloader (dfu over ble using nrfconnect on android...
Hi, I'm using the nrf connect mobile app and I want to connect multiple devices to the advertising device and I want them all to access the same characteristic at the same...
When I open SES it says that it cannot detect any j-link so it asks me to buy license. But shouldn't my nrf52840 dk board have on-board j-link that SES should detect? I check...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
Hi - I am wondering what is the power optimal way to read/write with the TWI module. I do a tx and rx with the TWI interface. I have something like this, from the examples...
Hi,
We have just almost finished develop a product which used nrf52840 as a data hub, a wifi module connect to nrf52840 through uart, and baudrate set to 460800, and also...
Hi ,
I am using the example "ble_app_uart".
I enable uart while receiving data from nus handler and turn it off after transmitting.
After I mondified the code, it can...
When trying to write the bootloader hex file to the device with nRFgo Studio, the following error message is displayed.
[nrf52840_xxaa_s140.hex programming failed: This...
Hello
I'm using SDK 15.2 on nRF52 DK to test the ble_app_multirole_lesc example.
I downloaded the code to nRF52 DK to act as central.
I commented the scan_start() function...
I take bootloader_secure_ble example for pca10056 build it and use hex file to program using nRFGo Studio get error verification Failed. if i programmed with keil then load...
HI,
I'm having a problem when I use the function nrf_drv_twi_xfer. The function returns the error code NRF_SUCCESS, but using the event handler I notice that I'm receiving...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
Dear all,
I am using SES, I have an application that relies on a softdevice. For it I developed a custom bootloader that DOES NOT rely on the softdevice and only transfers...
