Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
Hello,
I am using a nRF52840-DK with an HX711 in SES. I have been utilizing the code provided by Vidar Berg that can be seen here .
I downloaded the zip file, unzipped...
I'm developing the PCB schematic for a system using a nRF52 module that I found that suits my needs SKB369
At the same time I'm implementing a JTAG connector to flash my...
I was wondering: if the last sample of a buffer in the SAADC (using easyDMA and scan mode) is outside the limits, which interrupt would come first, the END or the LIMIT interrupt...
Hi, I am getting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event since I increased the size of MAX MTU to 203 from 23. At first, I received INVALID PARAM error and then found out...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
Target : NRF52832, SD S132 6.1.1. program on Eclipse.
Hello,
Intro :
I migrated to SDK 15.3 for my application and it works.
Then I migrated DFU to SDK15.3 too but...
Hello! I am developing a pcb based on nrf51822. I am trying to copy the layout of the PCA10028 at first. But I will not use the coaxial connector for an external antenna....
Hello!
I have next problem. When switching from backup power to main power, the controller loses data in RAM. If the backup voltage is below about 2.4V, then it is possible...
