Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I’m doing a project using NRF51822. We use P0.06 pin for PWM out while reading ADC from P0.01 P0.02 P0.03 & P0.04 .
As my experiment, when I’ve used P0.01 P0.02 P0.03 &...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
Good morning everyone,
I am writing a custom protocol using the RADIO module and I am having a hard time understanding the address organization.....
My protocol supports...
Hi,
I want to interface an analog front-end Device through NRF52840-DK board Using SPI Interface . I want waveforms to be as Below:
which driver I suppose to use is...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
What is the input impedance or input current of port P0_30/AIN6 when operating as an ADC input? Nominal or typical figures would be OK, but maximum and minimum figures would...
1、Nrf52810 does not have VDD_PA pin, whether it needs software control, whether any pin can be replaced？
2、Is there an example of the use of PA/LNA circuits in gazell and...
Hello,
The Gazell Pairing User Guide in the infocenter states that the AES ECB block is used for encryption & decryption. However, the product specification document for...
I have an issue with bonding between a PCA10040 running the sample Glucose app and an Acer tablet running Android 7 and nRF Toolbox. I have not seen the problem on a second...
Hello sir,
I am a beginner on NRF52840. I am using Nrfx_spim example for interfacing sensor with NRF Board.
I have done some driver about Reg_read and Reg_write. I tried...
I'm using the basic sdk example of ble_app_hrs_freertos example and created two tasks in it, namely Task1 and Task2. Now I have enabled preemption by setting "configUSE_PREEMPTION...
Hello everyone,
I write datas from my Client to my Server, but I don't really understand where I can retrieve my data on my server.
Is this function allowing to get...
