Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I'm making an firmware for the nrf52840 that communicate throw usb to a computer.
First I used the uart library that works fine but required the Jtag and Jling which...
I just cloned the latest zephyr from github and tried littlefs. However, the SPI pins have no traffic and CS line stays unchanged.
Is there something I forgot, since...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
Why is SES throwing an "Illegal value 0x21009168 written to register 66 (MSP_NS) ignored" message after "Download successful" when programming nRF5340's network core with...
Hello everyone,
I have questions concerning direct advertising. I have read this and other posts from several years ago which provided some useful information.
devzone...
Hello,
at the moment I am trying to get the NRF9160 Icarus Board to communicate with an ESP8266 Board within serial modem mode. I just need to send some AT commands through...
