Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi,
I am using nRF52832 with S132 softdevice and SDK version 11. I am getting bad memory address error code.
err_code = sd_ble_uuid_vs_add (&base_uuid, &ble_service->uuid_type...
Hi
I have a softdevice assert problem when i run the "nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject...
we use
peripheral: exemple ble_app_blinky
central: exemple_ble_app_bliky-c
Instead of a button we have a Switch.
When we set the Switch to "on" the led go on.
That...
Hi, I made a device with using NRF51822, named 'allb' the wearable device for babies.
http://myallb.com
We're planning to make a new version of it with using nRF52840...
The firmware used operate properly in the past, but it no longer does after we replaced the MCU(nrf52832).
During SOFTDEVICE_HANDLER_INIT, the MCU is stopped.
The previous...
I am working on a peripheral. This peripheral is IO display only. On the other side, the central is keyboard + display. I have a single, custom service with a single characteristic...
Hi All,
I did this tutorial : How Import a Keil uVision project Segger Embedded Studio - A Cross Platform IDE ,
but I dont know what did wrong. I still get this error...
While porting my app to the latest 14.0 SDK, it got a little stuck with the new sdh library. I was previously fetching all events through a custom poll & wait loop, but I...
When a packet sent out and get the TX_DS IRQ by nRF24l01+, the mode change to RX and read STATUS register then write the value to the STATUS register and write FLUSH_RX 0xff...
For the SDK13.0.0 the documentation say that HF clock is activated in nrf_drv_usbd_enable() / app_usbd_enable() but it is activated in nrf_drv_usbd_init() / app_usbd_init...
Hi,
We are planning to build a Mobile application for IoT involving Bluetooth communication. We came across a few part numbers of Nordic for this. We would like to know...
I had purchased the Red Bear Labs "Micro" board to develop code using their MK20 USB Dongle and Arduino.
If I "hack" the programming cable to emulate the "Micro" daughter...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
