Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Does nRF51822 have battery monitor?
pg 45 of datasheet says specifies "Absolute error when used for battery measurement" at:
Internal reference, input from VDD/3...
In the nrf52 OPS datasheet, for NVM and flash programming electrical specification (page 41) it has "Amount of writes in a block between erase" and Minimum for that is 181...
Hi all.
I need some suggestion how to use UART module in the nRF52 using nRF5_SDK_12.2.0 and the softdevice $132(it would affect?)
I would like use RX to receive information...
Hi.
Didn't find an exact answer for my question.
I'm using the ble_app_beacon example on my custom board based on nrf51822. While powering it from a coin battery, I measure...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...
Help!! I need to implement a dc motor position control and i have problem reading the encoder (too fast). I have seen that nrf51822 has a qdec peripheral. Any suggestions...
Hi,
I wanted to know if the UART pins can cause any issues if kept connected to usb (Rx/Tx pins stable to 3.3V) and directly to the GPIOs of the nRF52, while performing...
I've come across the following situation:
We have a device (nrf52) which uses fast advertising with whitelist after it has established a bond with a single phone. When...
Dear All,
I'm kinda getting desprate and would be very thankfull if somebody could help me.
I want to get two NRF24l01+ to communicate with each other. But it doesn...
hi, all
I met a communication problem between nrf52832 and nrf24le1, I used nrf52832 as receiver and nrf24le1 as transmitter, but unfortunately，nrf52832 can not receive...
We have a sensor product that has been in the field using the nRF8001 in no security required, just works mode for over a year. Recently, we had a request from a volume user...
I am using the ble_app_uart on the nrf51dk.RX is always enabled.I want to enable TX when data is to be transmitted and then disable it again.
I am using
NRF_UART0->TASKS_STOPTX...
Is there a way on the command-line to read the debug port (DP) register or access port (AP) register for nRF52 via the the nrjfprog program?
I do not want to write my own...
I'm new to the nRF51822. I've setup GCC and Make on Windows 10 and am using SDK 11. In all the examples of the SDK, flashing the newly made hex files (using GCC) with JLink...
We are working on a project that will operate in the MBAN frequency range of 2360-2390mhz. One of our current products utilizes the nRF24L chip, and we were interested in...
