Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
The SDK version is 16.0.0. I am using NRF 52840 DK and testing the BLE data transmission with the example project BLE_APP_UART. I am using NRF Connect Desktop to communicate...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
I expanded the button events based on example ble_peripheral ble_app_hrs by
and everything works fine (button press and button release events for all 4 buttons) till I...
Hi
We found abnormal current waveform when running GPS as 120s fix interval and 10s fix retry.
As below pic, the first plus is A-GPS seraching, from second plus is the...
Hi,
When I used nRF52840 dongle (connectivity_5.1.0_usb_with_s132_5.1.0.uf2 firmware) to receive peripheral device notifications, nRF52840 dongle can only receive 20 bytes...
Hi,
I'm not sure if SES support C++ compiler in nRF9160 project, I did add C++ source in CMakeList:
target_sources(app PRIVATE src/xxx.cpp)
It won't work, Does anyone...
hi,
I use the SDK16.0 ,to develop BLE touchpad on nRF52833,which is should set non-zero value for feature reports . And now,i have a problem,how to implement the FEATURE...
I made a custom board using nRF9160 and tested a very simple program.
However, it consumes high current compared to nRF9160 DK. I measured current flowing on VCC line of...
nRF52832 / SDK 14.2 / SD5.1.0
There might be two configurations to setup a PPI channel to assign some peripheral event to both timer capture & clear task:
nrf_drv_ppi_channel_assign...
Hello all,
Having a smallish problem seeing printk() output on my board. My board is an NRF9160 PCA10090 inspired board. Long story short, I can't see printk() stuff showing...
My application implements a beacon with services, and a buttonless BLE bootloader.
The application can start the bootloader in two ways.
The first method is executed locally...
Hi,
I am in the process of provisioning and configuring a 2-element light switch server node and a common light switch server. I am using the orginal exemple for the provisioner...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
