I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I have successfully detected my custom board (nrf52832 chip ) with nrf 52dk board and program it with blinky hex file given in SDK 15 version and works.
Now, i update...
Hi Guys
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Everything is working and the thingy sends its data to the nrf cloud.
My...
Hello, I am creating a peripheral with a totally custom set of services and characteristics (it will only talk to our custom central device). I've adapted the examples and...
Hello, in my application (adapted from ble_app_uart peripheral example of SDK 16.0) I am starting advertising using
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hi.
I'm working with both custom board based on nrf52840 and nrf52840-dk.
I just moved from the app_uart api to the abstract serial api.
I have noticed that when an...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_beacon’.
1) ‘ble_app_beacon’ will only broadcast...
Hello Devzone:
Would I be correct if I assume enabling APPROTECT should prevent writes into UICR? - for other readers, NO, IT CANNOT PROTECT AGAINST SOFTWARE READS/WRITES...
I am in the process of adding central functionality to ble_app_buttonless_dfu on a PCA10056.
When I call nrf_ble_scan_filter_set, the resulting builds debugging is broken...
Hi, I want to use the ADC peripheral (SKD16) and I am looking for the most energy-efficient way of doing this. I design a prototype that will be based on nRF52840 IC and will...
For a temperature sensing application, I am trying to implement a TWI interface with a TMP116 temperature sensor. I am using Keil uVision 5 to write the program. I have been...
I am attempting to port a BLE application to the nRF52840. The original application used a standard HCI serial interface so I am trying to adapt that to use the Nordic SoftDevice...
Calling the lte_lc_connect() function eventually leads to the code breaking on:
fault_s.S line 104
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE) /* force unlock interrupts...
Hi I am using NRF52 board to interface analog sensor and this board further transmit the data ro sink node. I am using saadc example but unable to get callback or my interrupt...
We have a set of custom boards I am working on debugging. I was able to get our software onto the device via nrf jprog tool by uploading a merged hex file (with SD + bootloader...