Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
I am using nrf5340 in my project. We had to replace flash memory but need a replacement with the same layout. So I am currently looking at w25q01jvzeim or w25q01jvzeiq . The...
I am building the: https://academy.nordicsemi.com/courses/cellular-iot-fundamentals/lessons/lesson-2-cellular-fundamentals/topic/lesson-2-exercise-2/ exercise and as part...
I have a characteristic whose value is an array of char, which can from 1 to 20 bytes long. Using SDK17 I can set a vlen attribute and use the function update_characteristic...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
Hi Devzone:
I saw two functions to write the retention register for DFU, nrf_power_gpregret_set and sd_power_gpregret_set.
What's the diffrence between
nrf_power_gpregret_set...
I'm experimenting with multiprotocol support on a PCA10056 (nRF52840) and the S340 softdevice. I need to use BLE and ANT+ at the same time, sending data to either ANT+ or...
What type of cable is required for the debug out, P19?
The specs for the port only say the number of pins, but not the pitch https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk...
nrf52840 packet transmitting time measurement for TOA or TDOA
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
What I’m trying to...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
Hi,
I am using nRF Connect (Desktop) v3.3.0 with a nRF51 dongle with the latest firmware to test my BLE device application.
My application contains 1 customized service...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
I need to share the LFCLK with an external device and I'm thinking on using an external oscillator like SiT1532AC-J5-DCC-32.768E
I'll set the LFCLKSRC registry as 111 (Apply...
I am setting up a build server that will take care of building our app for the nRF52 and creating the DFU files. For DFU package, I need nrfutil.
Everything is working fine...
The document infocenter.nordicsemi.com/.../nan_040.pdf shows the recommended sizes of the pads (0.275mm) and apertures for the stencil (0.3mm). To connect the inner rows of...
I have some nrf52382 nodes. I want to form two subnet in mesh.
if i using different provisioner to make subnet or something else ？
1. How to Create two subnets: Subnet...
Hi, I'm using metamotionR of Mbientlab that have nRF 52832 ( I attached the circuit of metamotionR )
but, I want to develop new firmware on this device. so, I started with...
Hello,
I have to implement ESB on nRF52 bare metal (using the RADIO peripheral). I can receive packets from the nRF24, but I need to implement the ACK, and I'm not sure...
