I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
After downloading and installing nrf mesh SDK as directed here https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-1-0/index . I'm not able to build any examples...
Hi, I am trying to use the RSSI viewer to scan RSSI values and verify the nearby beacons. But unfortunately RSSI viewer is NOT working and the following error message shown...
Hello.
I want to use the example of throughput with nRF52811.
I have changed it by looking at the nRF5 SDK Documentation, but it is not done.
(Software Development Kit...
I'm having issues building nRF5 SDK for Mesh v0.10.1-Alpha examples. On an Ubuntu 16.04 VM, I have installed the toolchain per the Debian/Ubuntu instructions and was able...
Hi,
I have two questions:
1) I am using ant bpwr tx example, SDK 15.2., Softdevice S212 v5.0.0, Segger embedded studio, nRF52832 DK and Garmin edge 520plus to display...
Hi there,
I have a custom built board with the nRF52840 and I'm trying to consistently transmit roughly 8 kilobytes per second or 64 kbits/s which seems way under the what...
Hello,
I'm working on a project that have with multirole to do, i have 3 device one act as master after a button is pressed, now i want to establish a connection between...
Hi,
I am having some issues with DFU and Keil.
I am loading Softdevice s140 v7.0.1 via nRF Connect and then programming a secure BLE bootloader using nrfjprog.
The bootloader...
Hi everybody,
I have a question about the number of data pakets which I can send with the BLE. Every data paket has a range of 20 Byte.
Now I want to send about 55 of...
Hi, I need to do some power analysis of an application I am working on. I have a Power Profiler Kit, but it will not work with nRF Connect currently.
I have two machines...
My application is on the nRF52840 Dongle using ESB protocol, receiving data from an number of PTXs, . The device appears as an HID.
I would like to add Buttonless DFU, without...
Hi,
I am new here and I have some issues with Zigbee reporting implementation.
I am trying to implement a reporting feature between a coordinator and an end device, which...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
