Normally when I connected the nPM1300 it would automatically display the battery status and settings,
I already switched up the npm1300 but none ofthem work here.
Is...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Hello,
We applied for some nrf9151 samples and designed a simple development board with reference to nrf9151 DK. However, there was an issue during testing that the SIM...
For background, a few years ago our company had a contractor build up a simple peripheral button and I wanted to use that hardware to learn nRF SDK for VS Code and the Zephyr...
I'm using the nrf52840, and I'm doing a project where the system needs to sleep for a long time, maybe more than 24 hours. Following this ticket, to go to sleep I just do...
Hello!
There are no hex files that are pre-made for the ble_app_interactive example. When I use VMware to run a Linux environment on Ubuntu to get an executable with gcc...
Hello,
I want to configure my nRF52840 development kit for counting input pulses on one of the GPIOs (Pin 13) in this case. I am using SEGGER Embedded Studio as IDE.
Here...
Hello,
we have a strange proglem with nrf52811 on an own board
after uart initialization and connecting the scope (Saleae) probe to the RX pin the device outputs fatal...
Hi,
I have a ARM core device like raspberry pi / orange pi etc, where I run a build and deploy server - basically compiling code and flashing to a target.
I have the...
We are trying to use serial port library for simple UART comms in IRQ mode at 115200, but experiencing what looks like stuck TX interrupt. PCA10040 with SDK 15.3.
In the...
I'm using nRF Connect v3.0.0 to run Getting Started Assistant v0.9.3 and get a message it is only compatible with 2.4.0 (very old). I can install and verify Tool Chain except...
Hi
I am trying to connect and bond a nrf52832 to Galaxy S6, Android 7.0 by OOB / NFC with the ble_nfc_pairing_reference_pca10040_s132 example.
I selected LE Secure Connections...
Hi nordic,we want to config nrf52832 as a wireless full-duplex serial port transmission module through nordic proprietary protocol，so the module can send and receive data...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
Hello,
I have problems setting the output RF power to +8 dBm during DTM test using the example dtm application. The example dtm application is used as it is provided with...
Hello,
i've been searching the forum for answers about Bluetooth certification but i'm very confused.
I want to use nRF52832 in my project, and i would like to make make...
I am trying to transferAdvertisement data from NRF52832 to Raspberry PI using BLE_app_UART example. I have updated the config as below,
app_uart_comm_params_t const comm_params...
Hi,
So this may seem like a stupid question but here goes. I've been trying to learn how to implement an IoT solution.
While trying to learn more about MQTT protocol...
Hi,
I'm trying to build the example found here: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
and the build is failing with this...
Hi!
I've been trying to connect the nRf9160 to an AWS IoT account following the directions here https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples...
