Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi, As we know that, we can see, the data has been sent to nRF Cloud in JSON format by Thingy91-PCA20035. And we can also see that, we have respective APIs like "cloud_send...
Hey,
I am getting a
warning: #47-D: incompatible redefinition of macro "STATIC_ASSERT_SIMPLE" (declared at line 215) warning: #47-D: incompatible redefinition of macro...
Hello, I am working on a ble application which is streaming data via ble notifications. I am currently queuing up the packets in the notification queue and keeping track of...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
Hello, Nordic.
I'm currently developing multiple sensor beacons and a scanner for asset tracking (scanner app based on ble_app_uart_c)
ble_app_uart_c has SCAN...
Hello,
Im designing a board with nRF52832 with acceleration sensor and BLE application, so for the esd protection, should there be an housing of some sort, what all can...
We're migrating from Zentri AMS002 chip to to nRF52840.
We use custom service UUID: "175f8f23-a570-49bd-9627-815a6a27de2a" in nRF firmware.
As attached images show, custom...
Hi!
We're developing a board where we would like to switch between normal power mode (VDD shorted with VDDH) and high power mode (VDDH as input and VDD in highZ or supplying...
Hello everyone. I'm looking for BT5.1 most supported at current moment chip - to have devboard and SDK with ability of direction finding. Which one you can recommend? As I...
We are working with nRF52, in that we want to select any fix channel of BLE. We does not want to use ADH mechanism due to form a whole network on one channel.
So can you...
