Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi,
We are using nRF9160 and want to use PSM & eDRX mode in one of our project. We referred 'Asset tracker Application' & found that lte_lc_psm_req() and lte_lc_edrx_req...
It would be great if I could move my project over to the Mac and use one less computer. But I wonder how well the tools work on MacOS platform. Are there any major limitations...
Hello,
the "Developing for nRF52810" user guide in the Infocenter says that to fully transfer a project to nRF52810 the defines DEVELOP_IN_NRF52832 and NRFX_COREDEP_DELAY_US_LOOP_CYCLES...
Hi
i am new with nRF52832. i am trying to run fatfs example program. But it shows Disk initialization failed. what is the reason for it?.
i am using segger embedded studio...
Hi,
I'm using SDK 15.2 & trying to combine hid keyboard with custom gatt service, but it was not advertising. When I debug, it got stuck on the line below with error code...
Hi.
I'd like to use nRF52840 in our project. Can I use the SoC and Zigbee SDK for commercial?
UPDATE!
Have I any limits if I will use SOC and Zigbee SDK for commercial...
Hello,
I follow " Configuring and performing DFU over Mesh" instraction and face with error after trying to transfer new app: "No response after opening COM port".
I do...
Hi,
I am trying to merge dfu with Beacon application. I have added all the required file in dfu example, but I am getting linker error for bsp.o file.
I am using sdk 14...
m_cb.adc_state is set to NRF_SAADC_STATE_CALIBRATION inside the function nrfx_saadc_calibrate_offset(), but the value is never changed to NRF_SAADC_STATE_IDLE, even is the...
Hello
I'm trying connect central to 4 peripheralPeripheral has 3 different customization services. When I connected to 4 peripheral, I encountered the problem of service...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I want to place the section of the FLASH area arbitrarily. And, for example, I want to place the following...
There is now a TI CC2451 Bluetooth module as a reference. Using nRF connect to monitor the log content, it is found that when the mobile phone is connected to Bluetooth and...
Hi everyone, I have a question about GPIOTE.
What happens if for example, GPIOTE is used to configure a pin to detect a low to high transition, but the pin is already...
Hello
I have a problem with restarting advertising after disconnect event.
There are two scenarios:
In this case everything works fine:
I start advertising
...
Hello,
I started with the template app and tried to do two things on a nRF52832 using Segger Studio:
1) advertise custom service
2) use Application Timer and App Scheduler...
