We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
Hello guys,
I wanted try run on NRF9160 hardware CC310 cryptographic module.
I installed all software and tried run secure_services demo. Thats works, cool!
In next...
Hi,
I am using SDK 15.2 and Softdevice S132 6.1.1. I'm having an issue getting my custom hardware built around the Laird BL652 (nRF52832) to start the program. It always...
Hi.
I need PC app communicate with my development board though BLE.
so I'm testing pca10059 with ble-pc-driver sdk.
I tested ble_app_att_mtu_throughput example with...
Hey, I am trying to sample from 10 analog sensors and stream the results via bluetooth. Since the nRF5 is on a board that only lets me access 5 Pins, I am using a 16:1 multiplexer...
Hi everyone!
At the begining I want to write what I'm using to make everything easier.
Device:
- NRF51822 xxAC ( This one ). - GSM module Simcom Sim 7000E ( This one...
I need to be able to upload my application to an nRF52832 through an ARM architecture Linux machine that I have remote access to. nrfjprog is not available for machines with...
Hello. I connected the Image transfer service (running on a nrf52840) to another nrf52840 running a modified BLE_NUS_C service.
However, a BLE packet won't be send out,...
Hello,
I have the following issue when trying to detect which GPIO triggered the interrupt:
For my low power application, I was trying to connect two switches to the...
Hi,
I'm in the process of designing my first prototype with the nRF9160 SiP. For the LTE antenna sub-circuit, I simply want to replicate (as much as possible) Nordic's reference...
Hello,
I am using custom nrf52832 PCB as central role. Also i have the peripheral with similar board . Peripheral communication is working properly if connected with the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Similar to WiFi and 802.15.4 where there are...
Hello,
Customer want to use
nRF51822 Bluetooth Smart Beacon Kit
with this requirements:
We need the most simple beacon. Additional sensors are not needed. Its main...
Hello Nordic team,
I'm using nrf52840 DK with SDK 15.3.0.
So I had an example sending data similarely to the ble_app_uart_c example that worked OK.
Basically I have...
Hello there!
We have a running prototype with an NRF24L01+ and ESB. But since it is not recommended for new designs, is there a successor for this setup?
Very low latency...
