Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hello, I am using a nrf52832 Soc for my development. I follow this https://github.com/bjornspockeli/custom_ble_service_example for the custom BLE service. I can do a specific...
Hi,
I am using nRF52840 Preview-DK with SDK v15.3.0
I am using the serial library to write to UART 1, while writing all goes well while I write less than 255 bytes...
Hi,
In the nus example of sdk 15 the device does not advertise if i comment out the uart_init() function. Why does this happen?
What is the relationship between the uart_init...
Hi guys,
After i provision for client node or server node by smartphone i have unicast address for server model or client model. How can i send message from client to server...
Ubuntu 19.04
SDK 15.3
nRF Connect v2.7.0
Nordic_HTS example both pre-compiled and self-compiled
Uploading to Fanstel BT832F and nRF52 DK
When I upload the example...
Hello,
My goal is to send a binary file by Bluetooth into the nRF52940 board from the terminal. I saw the ble_app_uart example. It seems to be exactly what I want to do...
Hello,
I need to use USB 2.0 connection as a USB MSC device as well have it communicate over a USB 2.0 connection to a Wi-Fi module.
I know there is a USB 2.0 built into...
I'm working on a project using nRF9160 DK.
How can you use MQTT+TLS in nRF9160?
Where should ca certificate file be stored?
I modified the code below in mqtt_simple...
hello i am using nrf52832 DK and working UART_APP_BLE , i want know where the data will be stored when we send any message through mobile to the device. can we see the received...
Hi, I am new at programming.
I am trying to program nRF51822 DK. But My Desktop can't appear J-Link Debugger as a USB drive.
I read some posts about that but I didn't...
Hi .......Clan
I am planning to make chatbox mean chatting (transferring the messages) between the central and peripherals even peripheral to peripheral , and device peripheral...
Im using MCP6S21 amplifier which takes input from some I to V converter and output of amplifier is connected to nrf52832 via I2C pins so how to change or vary gain of amplifier...
I am having a problem running MQTT_Simple on my nRF9160 DK.
The COM Port shows the following:
***** BUS FAULT ***** Precise data bus error BFAR Address: 0x4002a514 **...
Hi.
I am using the nrf9160 with the latest firmware and with all the instructions followed, I get this error . Faulting instruction address = 0x3648 Fatal fault in ISR!...
