Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
i have interfaced a ADC device in the nrf2 development kit,i am getting the values from the adc after using the SAADC example,
i want to implement the same with the...
Hi softdevice uses s130 The board is using nrf51 dk. The example uses the ble_app_beacon example from sdk12.3. if (switch_hit ()) { // NRF_POWER-> SYSTEMOFF = 1; // sd_power_system_off...
Hi Team,
Being trying to run the Thingy 52 mesh demo following : https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I am using pre-built .hex file Thingy_node_s132...
Hi there,
Recently I bought an LTE module which uses a nRF52840 as the main processor to control the modem, I want to erase the flash for that module and flash the project...
Hello,
Recently I added TWI to my project it keeps a low consumption before call TWI functions to read or write after this my current consumption increases and keeps above...
I'm using the nRF BLE Mesh SDK 2.2.0 with SES v3.5 (64bit for Windows)
Our hardware with nRF52832 using internal RC
I'm running the light_switch_proxy_server but with...
Hello,
I'm just starting to use the nRF Smart Beacon kit.
Is it possible to have the beacon toggle a GPIO on-board when the beacon is out of range of the phone/app?
...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I want to ask how to use app timer with scheduler.
Here is my implementation. I just use APP_TIMER_APPSH_INIT...
Hi All, I have tried to follow DFU documentation as well as many other things but nothing really worked well, I have some results but still cannot make my own code to be updatable...
Hi,
I am using nrf52 DK with BLE mesh Light-Switch Example. I was looking for changing behavior of the client/server. Is it possible to have both Client and server functionality...
I have a dev question about using the nRF Blinky app as an example for listing and showing services for multiple BLE devices without having to individually select each one...
Hello,
I want to use Radio Notification before connection event (ACTIVE signal). My routine takes 4 ms but Tprep time have huge range - from 167 us up to 1550 us, so even...
Hi
I had a problem which I want to send many packets in a loop using sd_ble_gatts_hvx(), but when the number is 5, the error code(NRF_ERROR_RESOURCES) is happened. Then...
Not sure if this is possible or not, but it's beginning to look as though the radio may be corrupting packets, either when sending them or receiving them or both, because...
