Hi, I've been given an nRF52 devkit and have been tasked with programming to generate a 2.4GHz signal. The requirement given to me is that simple. (I believe an RF expert...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hi everyone,
First of all ,Thanks for being such a supportive forum, I ask a lot of questions(I am a beginner to nordic and BLE)
I am using the example given in the sdk...
I am using nRF52832 IC with SDK v15.
I want to sample some data with 3200Hz sampling rate from SPI interface. There is an accelerometer connected via SPI interface. I...
We use nRF52832-QFAA-B0 and we found that PAN16 issue is still present, at least in some corner cases.
It happens when we put the chip in low-power mode with WFI ; at wakeup...
Can anyone help me?
Each service is working standalone.
There are two cases:
1.the BLE can't connect auto by iphone.
2.firmware can't receive notify...
I am hoping there is a Wiegand protocol file i can import into the project so i dont have to write it. Is there a function that has already been done i can import into my...
Hi Everyone
I was trying to get the BLE Uart working with the nrf52840.
Everything works fine, all files are compiling and running, but when i debug the code using segger...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
P0.5 - RTS
P0.6 - TX
P0.7 - CTS...
Hi.
I am developing a FW for nrf52832 and am using the nrf51 dongle as a testing tool using nrfconnect.
However, this is not working good because the dongle misses notification...
i need use flashwrite in my code, but i found sometims when i write data in flash, the BLE connecting sometimes is borken, i used this funciton flash_word_write(uint32_t ...
I am looking for help in doing a hardware reset. How can this be done? Do I need to make P0.21 active low so that P0.18 is enabled to be in RESET mode? This is for hardware...
To ship custom sensor data generated at 200 Hz from a BLE peripheral to a BLE Central over a GATT service I chose to start with template project in peripheral directory of...
Hi,
I'm using the nRF52 dev kit and try to use it as an Eddystone beacon. More precisely I want to use Eddystone EID and I would like to register the beacon using ECDH....
Hi, I have following issue and need some help. I am using SEGGER Embedded studio for ARM Release 3.4 build 2018052200 36079 with latest SDK on window 10 (64). Most of the...
Dear Support,
I’m working on uVision V5.25.2.0, using nRF5_SDK_15.0.0_a53641a.
My evaluation board is Rigado BMD-300.
Target: nrf52832_xxaa.
I tried using the printf...
The nRF52832 documentation has sections both for SPIM/SPIS (SPI peripheral using EasyDMA) and SPI (raw, direct write to the TXD register).
Indeed the nRF52832 does support...
