Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi,
We have custom board with STM32F407 as an application chip and BL652-SC-01 as a connectivity chip. When we worked on SDK 13 and softdevice 4.0.2 or 4.0.4 we had problem...
Hi, I have problem with using printf() in SEGGER RTT.
I've read tutorial and others about SEGGER RTT printf() problem, but they didn't work.
When I use printf() in RTT...
hi,
I found ble_app_multilink_central example under SDK but this is for LED button application.
Is it possible to configure the same example for NUS?
I worrying about...
I have app (based on buttonless_dfu) works on sdk 13, sd 3, nrf52832.
Now I try to migrate this app to newest SDK14, sd 5.
I can't resolve one issue. I have main.c and 7...
hi, I found ble_app_multilink_central example under SDK ,and make it work with NUS. Some problems bothered me.
When the amount of data reaches a certain amount, the transfer...
Hi,
Tried this getting started tutorial:
github.com/.../Nordic_SDK_User_Guide.md
When building project at the end, I get: (After trying max optimization)
linking...
Hi,
I am trying to program a custom board with ISP1507 chip from dynastream based on nRF52832 using the nRF52 DK. I have connected P20 on the DK to the chip as follows...
Hello, myCode: https://goo.gl/ggTei4 & Photo : https://goo.gl/Sq28tC
Please Help me with Dynamic NRF24L01 Mesh network
I have connected nodes via DHCP 01, 02 upto 05 to...
Hello everyone!
Do have any different between Read/Write internal flash with softdevice and non softdevice!
And how can I get example Read/Write internal flash with softdevice...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
