Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hello, I looked through the forum and tried some examples but it did not work for me.
My aim is to write cccd from peripherals side (Softdevice used S110).
As the result...
Dear Nordic Team.
I have using hardware P/N PCA10028(DK Board) and PCA10031(USB dongle) for both used chip 1422. I have tired to finding FW for ble-sniffer for 1422 chip...
I am using HID example with nrf52, where firmware allows connection from proprietary HID host, e.g. PC as virtual (BLE) keyboard. When connection is established, I use button...
I am working on implementing secure DFU.
I am currently using s132_nrf52_3.1.0 (production).
I believe I have the latest nrfutil which is 2.1.0 .
When I use command...
Hi,
I am working on RTC sample example in SDK12.0.0. The compare event in it triggers after 3 seconds. In my application I want to trigger the compare event every 10 seconds...
Hi.
I'm using NRF Connect v1.0 on a Windows 10 PC, together with an nRF52-DK (PCA10040).
It works nicely with the connectivity firmware 1.0.0 that the PC app offers to flash...
Hello, I'm looking into this particular issue and are now having some concerns. Namely:
My firmware size currently stands at 30k. It's not big, but definitely not...
Hi
I set the attribute request when receive a notify
case BLE_ANCS_C_EVT_NOTIF:
m_notification_latest = p_evt->notif;
notif_print(&m_notification_latest...
Hello, we are working on a project where we use the nrf52836 with a BMX055 sensor.
Due to BLE, we have to use a softdevice.
For now, we are using this version of the sdk...
Is there such a thing? For ultra-low, harvested power, how do you recommend powering the nRF5x: load switching Vcc or leaving Vcc connected and hold the reset pin low until...
Hello,
I have got the nRF52840-PDK, and I usually use CrossWorks, so I spun up a new project based on SDK 13, examples\peripheral\blinky and flashed this using default...
I would like to connect n antennas (through RF switch) to a single nRF52 that would do phase comparison between the n received signals. This is something related to I/Q sampling...
I know it is a pretty basic question but I can't manage to understand the documentation enough to pass the tutorial predeterminate code. If someone could help and tell where...
Hi,
I am trying to write a program which send data through notification. All is working, excepted that once the notifications are done, the device automatically disconnects...
I have an advertising device (NRF52DK+SD132_V3.1.0+SDK_12.2.0) where I whitelisted an address corresponding to my NRF51 Dongle (0xDA509C569622).
While the dongle is initiating...
