Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
hi all,
i am using SDK V8. i want to start and stop the RTC manually .i gone through rtc periheral example but still i am not getting . please help me. i am a beginneer...
Hello,
I am using the nRF51822 with SDK 10.0, S110 softdevice, and a SPI slave interface. The SPI slave interface works , but the standby power consumption of the nRF is...
Hi there,I am using s130, my device is now working at peripheral mode, it's advertising. I want to switch it into central mode by pressing a button. and switch back to peripheral...
If I had two devices, one set up as a peripheral and one as a central, what sort of factors do I need to consider to work out the lowest possible power consumption/average...
Hi,
I am sampling 2 200Hz signal using ADC and transmitting data using heart rate and battery service of ble_hrm(instead of using simulated data).
But since the connection...
I have the following setup:
nRF51 dongle
connectivity_115k2_with_s130_1.0.0.hex firmware
Windows 7 PC
nrf51-ble-driver_win_0.5.0
My app is written in...
Hi,
I see that you provide Master emulator API for windows (dll) that works with firmware for Master control panel application. Master control panel firmware, as the name...
Hello,
I try to set up an external signal for the LFCLK on a nrf52832. From this question :
I know the nrf52832 can do this (signal on XL1 pin, XL2 grounded).
...
Hello,
I am working on development to concurrent multiprotocol: BLE+2.4G proprietary. I am using timeslot feature in S132.
Because in my own 2.4g proprietary protocol, the...
I want to use feature reports in my HID project, but as far as I see this functionality is not fully included in ble_hids.c (SDK 11). I already managed to properly receive...
Hi,
I want to advertise in variable intervals and mostly only one advertisement at a time. I planned to do it like this:
1- start advertising with any interval (e.g...
Hello,
I followed the example for doing 128 bit UUID advertising using ble_app_uart example. The problem is, this seems to work if I run it when the radio and controller...
Hi,
I have my custom nRF51822 board based on Raytac MDBT40-P module. I am trying to program it with nRF51-DK(PCA10028). I could program it with mbed interface once or twice...
Hi,
I want to implement Advertising with the Timeslot API. I only need non-connectable advertisements but I want to be able to control the transmit power.
Which example...
