Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hai guys,
I am using nrf51dk, S130, and Keil to develop a simple project. My aim is to send the sensor data from the nrf51422 to the mobile app.
when no mobile is available...
I read this thread: nRF51 beacon high frequency scanning and advertising and have similar problem here.
Some repost from my electronics.stackexchange.com question
...
heya all,
I've tried folowing the guidlines for selecting correct SoftDevice for particular DK, but I am completely confused about the whole naming conventions and versions...
Hello,
I wants to store data in file or store data as non volatile .
I can't found any file related function.
Can any one help me how to store data as non volatile...
Im using nrf51. first I used bonding feature, for that I configured the characteristics with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM on read to trigger the bonding on IOS. ...
I am using SDK 11.0.0 and S132 on a nRF52832. In my application, my device can operate in BLE mode with the SoftDevice enabled or in custom RF mode with the SoftDevice disabled...
I need an accurate timer to generate pulses about 20ms. With simple timer this is workiong fine, but I need more then one timer simultaneously. So I would like to use app_timer...
Hi
I am working on NRF51822. I am using S120 ble_app_multilink_central example. I am trying to create a Timer1 interrupt of 1ms interval. My interrupt is working but interval...
Hi all,
I am trying to block connection from other devices to my nrf51dk board, except some specific devices. I used whitelist but it seem like the peripheral only block...
Hi,
I have just bought a nRF51822 Beacon Kit. The sticker on it shows that it is a PCA10006, Rev 1.2.0 2015.17 on it.
But I think that it is PCA20006.
What is the best...
Hi
I am getting some weird response from my nRF51-DK.
Situation 1:
When I try to flash it with the Blinky code (\sdk11\examples\peripheral\blinky\pca10028\s130\arm5_no_packs...
I'm trying to under the ble_app_multirole_lesc project and I'm a bit confused about calling sd_ble_auth_key_reply and sd_ble_lesc_dhkey_reply. If you are using Just Works...
Hi,
I am trying to send a HEX command to a device over UART at 9600bps using nRF52 DK, but it never works. However, it works with Arduino (so the receiving device should...
I have nRF52 Development Kit,after my first time programming the Firmware to my board.I can't erase or program it any more?
The nRF52 Development Kit can be connected with...
