Hello,
i am currently trying to build a minimal firmware for the nRF5340 on the Thingy:91x. Unfortunately my build failles to link zephyr/zephyr_pre0.elf:
My suspicion...
On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi,
I have two nrf51 devices one is the master and other a slave device. I need to lock these two devices permanently. What I mean is that these two devices can only connect...
Hi All,
I would like to setup my Eclipse and GCC for compiling and debugging C++ & mbed projects on nRF51 DK. The setup procedure explained in tutorial Development with...
Hi, I use SDK 10.0,
SoftDevice S110 8.0, S120 2.1, or S130 1.0, (I test various examples so I change SoftDevices)
iPhone 6 Plus (iOS 9.2.1), and Nexus 5 (Android 6.0...
Hello, i have a Nordic Nrf51822 ,PCA10001 V2.0.0 EVkit. I am desperately trying to run a beacon code in my EvKit. Since the PCA10001 V2.2.0 is old version ,it only supports...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
Hello,
I've created own characteristic and send it from proprietary board acting as peripheral to the Client in form of notifications. I use sd_ble_gatts_hvx() function...
Does anyone know of a good tool(s) for prototyping proprietary services and characteristics for App development? Our App dev team is ahaead of our firmware team and they want...
Hi,
I'd like to know how tp estimate of the best "timing accuracy" I could expect to achieve between an iOS device and a peripheral device. The objective is to make a specific...
Hi,
In my application I want to communicate nRF24L01+ with nRF51822 with dynamic length. Some settings are:
In nRF24L01+ side (reference: devzone.nordicsemi.com/.../)...
Hi,
Now I use these fun in ANT SD210 like below:
void MyFlashWrite(ble_ant_csc_t* cscdata)
{
uint32_t addr;
uint32_t patwr[3];
uint32_t pg_size;
uint32_t pg_num;...
what information does the nrfjprog.exe write to UICR(User Information Configuration Registers) register??
==========Tutorial of Flashing dfu bootloader to the nRF51 DK...
I want to use the ble sniffer to capture two peripherals connected to the master control panel.
with the ble sniffer I can only select one peripheral for capturing packets...
Hey there, I've posted this issue on the tutorial website and I came across a post stating that posting here will get me a quicker response. Here's my problem, when I tried...
In my application need to nrf8001 connect(bond) to e phone in a specific duration (for example 1 hours )and then disconnect and in one hour later bond again. In this duration...
Hi,
I am developing a Heart Rate application.
I need to ensure that i am flashing correct softdevice file through my application.
How can i do that?
Regards,
Sum...
