Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I've tried to set up my own BLE project as an exercise in understanding what's going on. It's going okay, with the exception that the device isn't advertising the data that...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
I'm working on a PC application (using nrf51-ble-driver_win_0.4.1 API) to connect a BLE device and discover BLE services.
Today, I'm tying to connect the Nordic dev kit...
When discovering services using nrf51-ble-driver_win_0.4.1 driver, some ID are received with type BLE_UUID_TYPE_UNKNOWN. So I assume they are 128bits. I then retrieve the...
I downloaded the BLE beacon app S110 v7.1.0 to a nRF51-DK board. The current measurement pins were attached to a 10 Ohm resistor.
I observed the AC-coupled voltage at one...
Hi. We've got a chip with a code QFACA10. I am trying to find out if there is the internal pull-down of SWD line or not. It seemed that adding an external pull-down had positive...
Hi all,
I want to know the effect on power consumption of pins input buffer on and off, does there are big differences between them?
Another question is, since there...
Hey everyone,
when i was trying to compile i got this error which says
._build\ble_app_bci.axf: Error: L6200E: Symbol SWI0_IRQHandler multiply defined (by nrf_notification_manager...
i have few question based on nordic i am using N51822.
1: does device goto sleep, while testing i see sometimes device gets automatically disconnected.
how can i solve...
Hi,
what would be a good option to create a BLE device like FLIC (flic.io).
i want to transmit only a few informations to the smartphone like 1,2,3,4 and the device shall...
Hi,
every time i try to call ble_bas_battery_level_update(&m_bas, 1); my application freeze and i can't get any response
Here is what i did:
1- copying ble_app_template_s110...
Hello folks
I have a custom PCB board with the attached layout diagram. I also have our firmware that was flashed on to the Nordic beacon kit and tested. I would like to...
Hello,
at the moment I try to add some more services to my BLE device. This goes wrong with err_code = 12 (NRF_ERROR_DATA_SIZE). With some search in the devZone I found...
