Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
I'm using SDK 7.1, PCA10028 and SD310 v2.0.1
Is there a project that implements OOB protection for bonding?
My device has no display, and a single button for input....
I'm getting Error 7 too few arguments to function 'lib_aci_set_local_data' C:\Users\nishant\Documents\Atmel Studio\6.2\ATmega_AdafruitLIB_nRF8001\ATmega_adafruitLIB_nRF8001...
Hello,
as far as I found out, a Peripheral that advertises will stop advertising as soon as it receives an incoming connection (BLE_GAP_EVT_CONNECTED). A central will however...
I'm using the nrf51822 with the IoT softdevice and SDK as an IPv6/6LoWPAN peripheral and Linux with a BLE dongle in the central role. Basically, I have everything working...
I'm trying to write 7 bytes (0x01 02 03 04 05 06 07) to my nrf51 Dongle with my own custom service running based on the Battery Service.
The problem is that I can only...
Why does it say that the nRF51822 has 1Mb/s and 2Mb/s data rates if it doesn't?
Quote from devzone: "6 * 20 B* 1/0.0075 s = 16 kB/s = 128 kbps".
And its only for S110...
Hi there
I am having problems with uart app on SDK V7.2
I have dowloaded Keil and all of the other demo's seem to be working but this one is not.
It will not connect...
Hi. i have a little problem.
For start, i want to use the referance Layout found here link text with the hardware description file of PCA10004.
So there is a simple method...
Previously, I used to load and debug my programs.
after a few months,
Today when I setup the environment again, now I can only compile and generate hex files from Keil....
Hi,
Now I am try to use sd_flash_page_erase() to erase a flash page.
Before I call it, I already stop all interrupt but I always get a error message "NRF_ERROR_NO_MEM...
Hello,
I am working with nRF51822 development kit (s130 softdevice). I want to use one software interrupt for my custom application. Is there any software interrupt available...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...